Table of Contents
A gentle crackle when you vape is normal — it is the sound of liquid turning to vapor. Loud popping and spitting is not: it means too much liquid is pooling on the coil, boiling instead of vaporizing. This guide explains the difference and gives you 7 tips to fix it.
Why vapes pop: the physics in 30 seconds
Your coil heats liquid on a saturated wick. When the balance is right, liquid vaporizes smoothly with a soft crackle. When the coil is flooded — too much liquid, too little heat — the excess liquid boils in bursts, and each burst is a pop. Pops big enough to throw hot droplets up the chimney are spit-back. So popping and spitting are the same problem at different volumes: flooding. The fixes in our spit-back guide apply here too.
7 tips to stop popping and spitting
1. Learn what normal sounds like
A light, steady crackle on the inhale is normal and healthy — it means the coil is vaporizing liquid. Loud, irregular pops, gurgling, and liquid reaching your mouth are the signs of flooding. If the sound is gentle and the flavor is clean, there is nothing to fix.
2. Check the wattage — too low is the usual culprit
A coil run below its printed wattage range cannot vaporize the liquid feeding it, so liquid pools and boils. If you are at the bottom of the range and popping, move toward the middle. (Too-high wattage causes the opposite problem: dry hits and burnt coils.) Stay inside the range printed on the coil.
3. Do not overfill, and do not over-prime
Fill to the fill line, not past it, and keep liquid out of the center chimney. When priming a new coil, use drops on the wicking holes — never dunk the coil in liquid, which floods it before you start. The full routine is in our priming guide.
4. Match the liquid to the coil
Thin (high-PG) liquids flow fast and flood easily — they are the more common popping culprit. Thick (high-VG) liquids flow slowly and starve the wick, causing dry hits instead. Use the ratio your coil was designed for: 50/50 for pods and mouth-to-lung coils, 70/30 VG for sub-ohm tanks. Our juice-matching guide has the full table.
5. Clear a flooded coil before you keep firing
If the tank gurgles or pops loudly, stop firing: you are boiling pooled liquid. Remove the tank, wrap the base in a paper towel, and blow gently through the mouthpiece to push excess liquid out of the chimney. Roll a paper towel into a thin wick and slide it down the chimney to absorb the rest. Then resume at the correct wattage.
6. Replace an old coil
A coil at the end of its life wicks unevenly — flooded in one spot, dry in another — and pops constantly. If popping persists after the fixes above and the coil is more than 1–2 weeks old, replace it. See our coil lifespan guide for the replacement signs, and our burnt-coil prevention guide for the habits that extend coil life.
7. Check the wire rules if you use temperature control
If you build coils or use temperature control mode, the wire type matters: nickel (Ni200) and titanium wire must ONLY be used in temperature control mode — never in wattage mode — and must never be dry-burned. Stainless steel works in both modes. There is no safe “wattage range” for nickel or titanium, and any table that lists one is wrong. Our temperature control guide has the full wire rules.
Popping by inhalation style
| Style | What happens | What to check |
|---|---|---|
| Mouth-to-lung (MTL) | Lower wattage, tighter draw; flooding shows as gurgling and spit-back | Wattage in range; 50/50 liquid; don’t overfill |
| Direct-to-lung (DTL) | Higher wattage, open airflow; flooding shows as loud pops and spit-back | Wattage in range; 70/30 VG liquid; coil not past its life |
Neither style is inherently more prone to popping — the cause is always the same: too much liquid, too little heat, or a dying coil. Match the setup to the style and the sounds settle down.
A note on safety
Popping itself is not dangerous — but a device that is hot, leaking, or behaving erratically should be checked, not pushed harder. The FDA’s battery safety tips cover the device side, and the NHS advises that nicotine vaping is less harmful than smoking and can help smokers quit.
Frequently asked questions
Why is my vape device spitting back?
Flooding: too much liquid pooling on the coil. The usual causes are overfilling, over-priming, wattage below the coil’s range, thin liquid in a coil that floods easily, or a dying coil.
What causes popping sounds in vape devices?
Liquid boiling in bursts on a flooded coil. Gentle crackling is normal; loud, irregular pops mean excess liquid is pooling instead of vaporizing smoothly.
How can I fix my popping vape?
Check the wattage is inside the coil’s range, clear the flooded chimney with a rolled paper towel, don’t overfill or over-prime, match the liquid ratio to the coil, and replace an old coil. The 7 tips above are the complete routine.
Is it normal for a vape to spit?
Occasional light spitting after filling or priming is common and clears quickly. Persistent spitting means flooding — fix the cause rather than living with it.
Is popping dangerous?
Popping on its own is not dangerous — it is a flooding symptom. But if the device is hot, leaking, or behaving erratically, stop using it and check the battery and coil before continuing.
For more on devices, coils, and safety, browse the Vaping & E-Liquids hub.
Affiliate Disclosure
The CakeHeights Editorial Team is committed to providing accurate, research-backed information about cannabis and hemp products. Some links on this page are affiliate links, meaning we may earn a commission at no extra cost to you if you make a purchase through them. Our recommendations are based on independent research, testing, and analysis. We only promote products we believe offer genuine value to our readers. Learn more →
Leave a Reply